Matek Systems H743-WING STM32H743VIT6 Flight Controller OSD 3~8S MPU6000 MicroSD Blackbox 5V/9V BEC for RC Airplane Fixed-Wing RC Drone FPV Racing
FC Specifications
MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
Baro: Infineon DPS310 (I2C2)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card slot (SDIO)
7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
13x PWM outputs(including “LED” pad)
2x I2C
1x CAN
6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
1x SPI3 breakout
USB/Beep Extender with Type-C(USB2.0)
Dual Camera Inputs switch
5V/9V(12V) for Camera/VTX power switch
High-precision Current Sense
ADC VB2 voltage divider: 1K:10K
ADC AirSpeed voltage divider: 10K:10K
INAV TR/SA VTX control: Yes
Beeper : Yes
RSSI: Yes
Analog Airspeed sensor: Yes
Digital Airspeed sensor: Yes
Static power 160mA@5V
FC Firmware
ArduPilot(ChiBiOS): MATEKH743
INAV: MATEKH743 (To be supported soon)
BetaFlight: MATEKH743
PDB
Input voltage range: 9~36V (3~8S LiPo) w/TVS protection
2x ESC power pads
Battery Voltage Sensor: 1:10 (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
Current Senor: 132A, 3.3V ADC (Scale 250 in INAV, 40 A/V in ArduPilot)
Sense resistor: 60A continuous, 132A burst.
BEC 5V output
Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
Continuous current: 2 Amps, Max.3A
BEC 9V /12V output
Designed for Video Transmitter, Camera, Gimbal ect.
Continuous current: 2 Amps, Max.3A
12V option with Jumper pad
BEC Vx output
Designed for Servos
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current: 8 Amps, Max.10A
BEC 3.3V output
Linear Regulator
Continuous current: 200mA
Physical
Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 54 x 36 x 13 mm
Weight: 30g with USB extender
ArduPilot Mapping
PWM PWM1~PWM13 are Dshot and PWM capable. However, mixing Dshot and normal PWM operation for outputs is restricted into groups, ie. enabling Dshot for an output in a group requires that ALL outputs in that group be configured and used as Dshot, rather than PWM outputs. If servo and motor are mixed in same group, make sure this group run lowest PWM frequency according to the servo specification. ie. Servo supports Max. 50Hz, ESC must run at 50Hz in this group. |
S1 | PB0 | 5 V tolerant I/O | PWM1 GPIO50 | TIM8_CH2N | Group1 |
S2 | PB1 | 3.3 V tolerant I/O | PWM2 GPIO51 | TIM8_CH3N | ||
S3 | PA0 | 5 V tolerant I/O | PWM3 GPIO52 | TIM5_CH1 | Group2 | |
S4 | PA1 | 5 V tolerant I/O | PWM4 GPIO53 | TIM5_CH2 | ||
S5 | PA2 | 5 V tolerant I/O | PWM5 GPIO54 | TIM5_CH3 | ||
S6 | PA3 | 5 V tolerant I/O | PWM6 GPIO55 | TIM5_CH4 | ||
S7 | PD12 | 5 V tolerant I/O | PWM7 GPIO56 | TIM4_CH1 | Gourp3 | |
S8 | PD13 | 5 V tolerant I/O | PWM8 GPIO57 | TIM4_CH2 | ||
S9 | PD14 | 5 V tolerant I/O | PWM9 GPIO58 | TIM4_CH3 | ||
S10 | PD15 | 5 V tolerant I/O | PWM10 GPIO59 | TIM4_CH4 | ||
S11 | PE5 | 5 V tolerant I/O | PWM11 GPIO60 | TIM15_CH1 | Group4 | |
S12 | PE6 | 5 V tolerant I/O | PWM12 GPIO61 | TIM15_CH2 | ||
LED | PA8 | 5 V tolerant I/O | PWM13 GPIO62 | TIM1_CH1 | Group5 | |
SERVO13_FUNCTION 120, NTF_LED_TYPES neopixel | ||||||
ADC | No pad 1K:10K divider builtin |
PC0 | 0~36V | on board battery voltage | BATT_VOLT_PIN BATT_VOLT_MULT |
10 11.0 |
No pad | PC1 | 0~3.3V | on board current sensor | BATT_CURR_PIN BATT_AMP_PERVLT |
11 40 |
|
VB2 Pad 1K:10K divider builtin |
PA4 | 0~36V | VB2 ADC | BATT2_VOLT_PIN BATT2_VOLT_MULT |
18 11.0 |
|
CU2 Pad | PA7 | 0~3.3V | CU2 ADC | BATT2_CURR_PIN BATT2_AMP_PERVLT |
7 / |
|
RSSI Pad | PC5 | 0~3.3V | RSSI ADC Analog RSSI |
RSSI_ANA_PIN RSSI_TYPE |
8 1 |
|
AirS Pad 10K:10K divider builtin |
PC4 | 0~6.6V | AirS ADC Analog Airspeed |
ARSPD_PIN ARSPD_TYPE |
4 2 |
|
I2C | I2C1 CL1/DA1 |
PB6/PB7 | 5 V tolerant I/O | Digital Airspeed I2C | ARSPD_BUS ARSPD_PIN |
1 65 |
MS4525 MS5525 DLVR-L10D |
ARSPD_TYPE | 1 3 9 |
||||
Compass | COMPASS_AUTODEC | 1 | ||||
I2C2 CL2/DA2 |
PB10/PB11 | 5 V tolerant I/O | on board Baro DPS310 | |||
CAN | CAN1 | PD0/PD1 | 5 V tolerant I/O | F103/F303 CAN Node | CAN_D1_PROTOCOL CAN_P1_DRIVER |
1 1 |
CAN GPS | GPS_TYPE | 9 | ||||
CAN Compass | COMPASS_TYPEMASK | 0 | ||||
CAN Airspeed sensor | ARSPD_TYPE | 8 | ||||
UART | USB | PA11/PA12 | 5 V tolerant I/O | USB | console | SERIAL0 |
RX7 TX7 RTS7 CTS7 | PE7/8/9/10 | 3.3 V tolerant I/O | UART7 | telem1 | SERIAL1 | |
TX1 RX1 | PA9/PA10 | 5 V tolerant I/O | USART1 | telem2 | SERIAL2 | |
TX2 RX2 | PD5/PD6 | 5 V tolerant I/O | USART2 | GPS1 | SERIAL3 | |
TX3 RX3 | PD8/PD9 | 5 V tolerant I/O | USART3 | GPS2 | SERIAL4 | |
TX8 RX8 | PE1/PE0 | 5 V tolerant I/O | UART8 | USER | SERIAL5 | |
TX4 RX4 | PB9/PB8 | 5 V tolerant I/O | UART4 | USER | SERIAL6 | |
TX6 RX6 | PC6/PC7 | 5 V tolerant I/O | USART6 | RC input/Receiver | ||
RX6 | SBUS/IBUS/DSM | |||||
RX6 | PPM |
ArduPilot Relay
* Camera-1 and Vsw On by default
* Make sure 2 cameras are set with identical video format, both PAL or both NTSC.
# GPIOs
PD10 PINIO1 OUTPUT GPIO(81) //Vsw pad power switch
PD11 PINIO2 OUTPUT GPIO(82) //Camera switch
# RCx_OPTION: RC input option
28 Relay On/Off
34 Relay2 On/Off
35 Relay3 On/Off
36 Relay4 On/Off
e.g.
RELAY_PIN 81 //Vsw GPIO
RC7_OPTION 28 //Relay On/Off, Use CH7 of Transmitter to switch Vsw
RELAY_PIN2 82 //Camera switch GPIO
RC8_OPTION 34 //Relay2 On/Off, Use CH8 of Transmitter to switch camera
or
* RELAY_PIN3 81 //Vsw GPIO
* RC9_OPTION 35 //Relay3 On/Off, Use CH9 of Transmitter to switch Vsw
* RELAY_PIN4 82 //Camera switch GPIO
* RC10_OPTION 36 //Relay4 On/Off, Use CH10 of Transmitter to switch camera
The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.
Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory
Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.
H734-Wing vs Wing Series
WING series | H743-WING | F765-WING | F722-WING | F405-WING |
Launch | Aug.2020 | Aug.2019 | Dec.2018 | Apr.2018 |
INAV Target | To be updated | MatekF765 | MatekF722SE | MatekF405SE |
Ardupilot Target | MatekH743 | MatekF765-WING | / | MatekF405-WING |
Firmware | INAV | INAV,BF | INAV | INAV |
ArduPilot | ArduPilot | BetaFlight | ArduPilot | |
MCU | 480MHz | 216MHz | 216MHz | 168MHz |
STM32H743 | STM32F765 | STM32F722 | STM32F405 | |
2MB Flash | 2MB Flash | 512KB Flash | 1MB Flash | |
IMU | MP6000 & ICM20602 | MP6000 & ICM20602 | MP6000 | MP6000 |
BARO | DPS310 | BMP280 | BMP280 | BMP280 |
OSD | AT7456E | AT7456E | AT7456E | AT7456E |
BlackBox | MicroSD(SDIO) | MicroSD(SDIO) | MicroSD | MicroSD |
Dual Camera In | Yes | Yes | Yes | / |
5V/9V Switcher | Yes | Yes | Yes | / |
Current | High precision | High precision | High precision | 104A |
Sense | 132A | 132A | 132A | |
Max.Voltage | 36V(8S) | 36V(8S) | 36V(8S) | 30V(6S) |
PWM outputs | 13 | 13 | 8 | 9 |
UART | 7 | 7 | 5 | 6 |
CAN | 1 | / | / | / |
Uart Inversion | All | All | All | RX2 |
5V | 2A | 2A | 2A | 2A |
9V | 2A | 2A | 2A | 2A |
Vx | 8A/10A | 8A/10A | 5A | 5A |
3.3V | 200mA | 200mA | 200mA | 500mA |
Size | 54×36 | 54×36 | 54×36 | 56×36 |
Weight | 30g | 26g | 25g | 25g |
Tips
ArduPilot Firmware ” MATEKH743″
* Only beta/latest ArduPilot firmwares after Jun.25 support the onboard barometer currently.
* https://firmware.ardupilot.org/Plane/latest/MatekH743/
* https://firmware.ardupilot.org/Copter/latest/MatekH743/
* H743-WING has betaflight firmware preloaded for QC
* If you flash ArduPilot firmware via BetaFlight configurator. there is a known issue that flash process will freeze at 50% if “full chip erase” is selected. Disable full chip erase when flashing, then reset to default in Mission Planner after flashing.
* It is highly recommended to use STM32CubeProgrammer to erase MCU and upload firmware http://www.mateksys.com/?p=6905
H743-WING Quick Start Guide, click here
Package Included:
1x H743-WING
1x USB/Beep Extender
1x 20cm SH-4P to GH-4P cable for CAN port
1x 20cm SH-6P to SH-6P cable for USB extender.
Dupont 2.54 pins (Board is shipped unsoldered)
(1) FREE Shipping 10 - 15 business days, (2) Standard Shipping 7 - 12 business days.
Shipping and Delivery Estimates
We ship in-stock orders as soon as possible. This is often within two business days, but there are situations where it may take longer. All estimates are based on business days.
Note:
(1) The shipping time mentioned above refers to the estimated time of business days that the shipment will take after an order has been shipped.
(2) Business days do not include Saturday/Sunday and any public holidays.
(3) These estimates are based on normal circumstances and are not a guarantee of delivery times.
(4) We are not responsible for the failures or delays in delivery resulting from any force majeure event, such as natural disaster, bad weather, war, customs issues, and any other event beyond our direct control.
for more information please visit our Shipping Policy Page.
Women's Sizing & Fit Guide
Please be aware that most of our clothing is Juniors' sizing, which runs smaller than regular US / European Women sizing. Refer to the measurements chart for each individual product to determine the best size for you. Product specific size chart and information can be found in product description or in product picture gallery.
Our team does it's best to include accurate size details and measurement of each item in the product descriptions. If you have questions regarding sizing or any other information on a specific item, please email us at support@mrslm.com for specific details.
Find the best size
When comparing your measurements to those listed on the site, make sure to check if the fabric is stretchy or not. If it is, it can stretch an inch or more.
- Bust: Wrap the measuring tape loosely around the fullest part of your bust to ensure a comfortable fit.
- Waist: Measure the narrowest part of your natural waist, holding the measuring tape loose enough to fit comfortably.
- Hips: Drape the measuring tape around the widest part of your hips, resting the tape comfortably against your body.
- Length: For tops and dresses, measure from the top of your shoulder to the hem. For strapless dresses, measure from the highest part of the neckline to the hem. For pants and skirts, measure from the top of the waist to the hem.
- Sleeve: With your arm outstretched, measure from the base of your neck to the end of the sleeve hem to determine where the sleeve length will fall on you.
Size Chart
Dresses Size Chart
DRESSES SIZE IN INCHES |
||||
SIZE | US / CAN | BUST | WAIST | HIPS |
XS | 0 | 31"-32" | 24"-25" | 34"-35" |
S | 2-4 | 33"-34" | 26"-27" | 36"-37" |
M | 6-8 | 35"-36" | 28"-29" | 38"-39" |
L | 10-12 | 37"-39" | 30"-32" | 40"-42" |
XL | 14 | 40"-42" | 33"-35" | 43"-45" |
DRESSES SIZE IN CM |
||||
SIZE | US / CAN | BUST | WAIST | HIPS |
XS | 0 | 78.7-81.2 | 60.9-63.5 | 86.3-88.9 |
S | 2-4 | 83.8-86.3 | 66-68.5 | 91.4-93.9 |
M | 6-8 | 88.9-91.4 | 71.1-73.6 | 96.5-99 |
L | 10-12 | 93.9-99 | 76.2-81.2 | 101.6-106.6 |
XL | 14 | 101.6-106.6 | 81.2-88.9 | 109.2-114.3 |
Tops Size Chart
TOPS SIZE IN INCHES |
|||
SIZE | US / CAN | BUST | WAIST |
XS | 0 | 31"-32" | 24"-25" |
S | 2-4 | 33"-34" | 26"-27" |
M | 6-8 | 35"-36" | 28"-29" |
L | 10-12 | 37"-39" | 30"-32" |
XL | 14 | 40"-42" | 33"-35" |
TOPS SIZE IN CM |
|||
SIZE | US / CAN | BUST | WAIST |
XS | 0 | 78.7-81.2 | 60.9-63.5 |
S | 2-4 | 83.8-86.3 | 66-68.5 |
M | 6-8 | 88.9-91.4 | 71.1-73.6 |
L | 10-12 | 93.9-99 | 76.2-81.2 |
XL | 14 | 101.6-106.6 | 83.8-88.9 |
Bottoms Size Chart
BOTTOMS SIZE IN INCHES |
|||
SIZE | US / CAN | WAIST | HIPS |
XS | 0 | 24"-25" | 34"-35" |
S | 2-4 | 26"-27" | 36"-37" |
M | 6-8 | 28"-29" | 38"-39" |
L | 10-12 | 30"-32" | 40"-42" |
XL | 14 | 33"-35" | 43"-45" |
BOTTOMS SIZE IN CM |
|||
SIZE | US / CAN | WAIST | HIPS |
XS | 0 | 60.9-63.5 | 86.3-88.9 |
S | 2-4 | 66-68.5 | 91.4-93.9 |
M | 6-8 | 71.1-73.6 | 96.4-93.9 |
L | 10-12 | 76.2-81.2 | 101.6-106.6 |
XL | 14 | 83.8-88.9 | 109.2-114.3 |
Denim Size Chart
DENIM SIZE IN INCHES |
||||
WAIST SIZE | JUNIOR SIZING | WAIST | LOW WAIST | HIPS |
24 | 0 | 24"-25" | 26"-27" | 32"-33" |
25 | 1 | 25"-26" | 28"-29" | 33"-34" |
26 | 3 | 26"-27" | 30"-31" | 34"-35" |
27 | 5 | 27"-28" | 31"-32" | 35"-36" |
28 | 7 | 28"-29" | 32"-33" | 36"-37" |
29 | 9 | 29"-30" | 33"-34" | 37"-38" |
30 | 11 | 30"-31" | 34"-35" | 38"-39" |
31 | 13 | 31"-3" | 35"-36" | 39"-40" |
32 | 15 | 32"-33" | 36"-37" | 40"-41" |
DENIM SIZE IN CM |
||||
WAIST SIZE | JUNIOR SIZING | WAIST | LOW WAIST | HIPS |
24 | 0 | 60.9-63.5 | 66-68.5 | 81.2-83.8 |
25 | 1 | 63.5-66 | 71.1-73.6 | 83.8-86.3 |
26 | 3 | 66-68.5 | 76.2-78.7 | 86.3-88.9 |
27 | 5 | 68.5-71.1 | 78.7-81.2 | 88.9-91.4 |
28 | 7 | 71.1-73.6 | 81.2-83.8 | 91.4-93.9 |
29 | 9 | 73.6-76.2 | 83.8-86.3 | 93.9-96.5 |
30 | 11 | 76.2-78.7 | 86.3-88.9 | 96.5-99 |
31 | 13 | 78.7-81.2 | 88.9-91.4 | 99-101.6 |
32 | 15 | 81.2-83.8 | 91.4-93.9 | 101.6-104.1 |
Swimwear Size Chart
SWIMWEAR SIZE IN INCHES |
||||
SIZE | US / CAN | BUST | WAIST | HIPS |
XS | 0 | 31"-32" | 24"-25" | 33"-34" |
S | 2 | 33"-34" | 26"-27" | 35"-37" |
M | 4 | 35"-36" | 28"-29" | 37"-38" |
L | 6 | 37"-39" | 30"-32" | 39"-41" |
XL | 8 | 40"-42" | 33"-35" | 42"-44" |
SWIMWEAR SIZE IN CM |
||||
SIZE | US / CAN | BUST | WAIST | HIPS |
XS | 0 | 78.7-81.2 | 60.9-63.5 | 83.8-86.3 |
S | 2 | 83.8-86.3 | 66-68.5 | 88.9-93.9 |
M | 4 | 88.9-91.4 | 71.1-73.6 | 93.9-96.5 |
L | 6 | 93.9-99 | 76.2-81.2 | 99-104.1 |
XL | 8 | 101.6-106.6 | 81.2-88.9 | 106.6-111.7 |
Shoes Size Chart
US | EURO | UK | AUS | JAPAN | CHINA |
5 | 35-36 | 3 | 3.5 | 21.5 | 35 |
5.5 | 36 | 3.5 | 4 | 22 | 35.5 |
6 | 36-37 | 4 | 4.5 | 22.5 | 36 |
6.5 | 37 | 4.5 | 5 | 23 | 36.5 |
7 | 37-38 | 5 | 5.5 | 23.5 | 37 |
7.5 | 38 | 5.5 | 6 | 24 | 37.5 |
8 | 38-39 | 6 | 6.5 | 24.5 | 38 |
8.5 | 39 | 6.5 | 7 | 25 | 38.5 |
9 | 39-40 | 7 | 7.5 | 25.5 | 39 |
9.5 | 40 | 7.5 | 8 | 26 | 39.5 |
10 | 40-41 | 8 | 8.5 | 26.5 | 40 |
11 | 41-42 | 9 | 9.5 | 27.5 | 41 |
Attention: This guide provides general sizing information only, and fit can vary depending on style and brand. For more specific sizing information on the product, please refer to product description.
NOTE:
- All models are wearing size small in tops and dresses, and size 1, 3, or 5 in jeans depending on their body type.
- Most kalles jeans & dresses have some stretch, please refer to product description for fabric details.
- Most kalles bottoms have an inseam of 31-34” depending on the cut and style. Sizing may vary depending on cut and style.